Wake Lamp: Difference between revisions

Revision as of 21:45, 2021 October 8

I made a ceiling lamp based on what a resting rowing shell would look like from under water.

		Actioned 2021-10-31

get picture / video

I reviewed videos and photos to understand what this would actually look like. Then I 3D modelled the belly of a rowing shell and the blades of some oars and 3D printed them. I Laser cut (or rather engraved) the shapes of the waves around the shell and the oars out of a sheet of translucent acrylic. I glued the 3d printed parts on the bottom of the acrylic sheet. Then I built the body of the lamp, and installed RGB LEDs against a randomly reflective background out of crushed up aluminum foil. I then programmed an Arduino to create the appearance of the change of colour and flickering under water in the LEDs.

@@ Line 1: / Line 1: @@
-A ceiling lamp based on a resting rowing shell from underwater.
+[[Internal:Wake lamp]]
-== Size ==
+I made a ceiling lamp based on what a resting rowing shell would look like from under water.
-" diameter circle-ish; that means 75.4" circumference, ie 1.9m
-* also see [[#Power Supply]]
-== Electronics ==
+{{TD computer|}} get picture / video
-LEDs and Arduino ordered from adafruit, order 469886, justthis1please!
-=== Arduino ===
-* [https://www.adafruit.com/products/1315 Arduino Micro w/o headers] - $24.95
-==== Arduino Size ====
-.7" x 1.9" x 0.4" (17.77mm x 49.52mm x 11.59mm)
-=== LEDs ===
+I reviewed videos and photos to understand what this would actually look like. Then I [[3D modelled]] the belly of a rowing shell and the blades of some oars and [[3D printed]] them. I [[Laser cut]] (or rather engraved) the shapes of the waves around the shell and the oars out of a sheet of translucent acrylic. I glued the 3d printed parts on the bottom of the acrylic sheet.
-==== white ====
+Then I built the body of the lamp, and installed RGB LEDs against a randomly reflective background out of crushed up aluminum foil. I then programmed an [[Arduino]] to create the appearance of the change of colour and flickering under water in the LEDs.
-* https://www.adafruit.com/products/357
-* 60 LEDs/m, max 1.2A/m at full brightness
-* 1200mA / 60 LEDs = 20mA / LED
-* installed length for 99 LEDs --> 1980mA at full brightness
-** measuerd at 1950-1960mA
-** suspect this is why things are getting hot
-==== colour LED WS2812B ====
-* 34 LEDs installed
-* measured for combined (arduino and colour LEDs) at 1200 - 1250mA
-* datasheet: https://www.adafruit.com/datasheets/WS2811.pdf
-* bought on ebay [http://www.ebay.com/itm/50Pcs-WS2812B-LED-With-Heatsink-10mm-3mm-DC5V-5050-SMD-RGB-WS2811-IC-Built-in-/281270793101?pt=US_Lighting_Parts_and_Accessories&hash=item417d0bb38d]
-=== Power Supply ===
+[[Category:Personal Project]]
-* need 2A for each 5V (colour), 12V (white)
+[[Category:Arduino]]
-* 0.5A, so 60W
+[[Category:Laser Cutting]]
-* ebay [http://www.ebay.com/itm/12V-5V-AC-Adapter-Hard-Disk-Power-Supply-For-Hard-Disk-Drive-Black-T1K-/380647145774]
+[[Category:3D Modelling]]
-* 10.7 x 4 x 3cm
+[[Category:3D Printing]]