Custom Shampoo Rack - Revision history

Ttenbergen at 04:06, 2021 November 1

2021-11-01T04:06:26Z

← Older revision		Revision as of 21:06, 2021 October 31
Line 1:		Line 1:
	{{Project		{{Project
	\|shortDescription=C		\|shortDescription=Custom stand to store shampoo bottles upside down.
			\|longDescription=I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.

			I [[3D modelled]] the rack and then [[laser cut]] it. The rack has been in my shower for several years and the idea works. Some of the contents of the bottles actually separate a bit because they never change orientation, so this setup has a drawback, but not nearly enough so to give this up.
			\|skillSet=Laser Cutting; Graphic Design
			\|projectType=Personal Project
			\|northForge=Yes
	}}		}}
	I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.

	{{To Do \| Photo! }}		{{To Do \| Photo! }}

	I [[3D modelled]] the rack and then [[laser cut]] it. The rack has been in my shower for several years and the idea works well. I think some of the bottles may actually separate a bit because they never change orientation, this could be a drawback.

	~~[[Category:Personal Project]]~~
	~~[[Category:Laser Cutting]]~~
	~~[[Category:Graphic Design]]~~

Ttenbergen at 04:03, 2021 November 1

2021-11-01T04:03:12Z

← Older revision		Revision as of 21:03, 2021 October 31
Line 1:		Line 1:
	{{Project}}		{{Project
			\|shortDescription=C
			}}
	I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.		I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.

Ttenbergen at 03:50, 2021 November 1

2021-11-01T03:50:52Z

← Older revision		Revision as of 20:50, 2021 October 31
Line 1:		Line 1:
			{{Project}}

	I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.		I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.

	{{~~TD computer~~\|}} ~~Photo!~~		{{To Do \| Photo! }}

	I [[3D modelled]] the rack and then [[laser cut]] it. The rack has been in my shower for several years and the idea works well. I think some of the bottles may actually separate a bit because they never change orientation, this could be a drawback.		I [[3D modelled]] the rack and then [[laser cut]] it. The rack has been in my shower for several years and the idea works well. I think some of the bottles may actually separate a bit because they never change orientation, this could be a drawback.

Ttenbergen: Created page with "I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bott..."

2021-10-09T04:55:31Z

Created page with "I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bott..."

New page

I wanted stand for my shampoo bottles so I can stand them upside down (like the condiments at Burrito Splendito) so I don't have to wait for them to run to the top of the bottle. I also wanted to play with a [[laser cut]] tab and slot design in acrylic.

{{TD computer|}} Photo!

I [[3D modelled]] the rack and then [[laser cut]] it. The rack has been in my shower for several years and the idea works well. I think some of the bottles may actually separate a bit because they never change orientation, this could be a drawback.

[[Category:Personal Project]]
[[Category:Laser Cutting]]
[[Category:Graphic Design]]